You are not logged in.
---- UPDATE ---
I stopped the wiki page on virt-manager and instead i started a new one
on using Qemu in CommandLineInterface. Using QEMU from a CLI
---- endupdate ---
I started a wiki page on virt-manager in the https://wiki.devuan.org
It's in the sandbox in https://wiki.devuan.org/Sandbox/Virt-Manager .
I occasionaly use virt-manager and in now as in the past i had again difficulties in setting
it right in devuan. So i think a wiki page could function as focus in order to collect
instructions and tips to smooth things out.
devuan wiki needs i guess some thinking about how to organize things so for
time being i put it in the sandbox.
Also for now i choosed to use as name the package name that i used for installation.
Any corrections and suggestions are welcomed .
Last edited by chomwitt (2024-03-26 08:32:48)
Devuan(Chimaera)(Daedalus) DS+WM: XorgX11server+StumpVM
Offline
Hello.
For better experience, i use these packages:
qemu-kvm libvirt-clients libvirt-daemon libvirt-daemon-system bridge-utils virtinst virt-manager
Also, don't forget to add your user to libvirt and libvirt-qemu groups:
adduser username libvirt
adduser username libvirt-qemu
Last edited by stopAI (2024-03-15 12:34:05)
Offline
qemu-kvm is no part of Daedalus.
Last edited by chomwitt (2024-03-15 15:56:19)
Devuan(Chimaera)(Daedalus) DS+WM: XorgX11server+StumpVM
Offline
I'm sorry. An error occurred. I wanted to write
qemu-system-misc
Offline
stopAI thanks for the suggestion. Searching recursively in virt-manager dependencies ... ->
$ apt-cache depends --recurse --no-suggests --no-conflicts --no-breaks --no-replaces --no-enhances virt-manager | grep "^\w" | sort -u | grep 'virtinst\|libvirt-clients\|libvirt-daemon\|qemu-system-misc\|bridge'
libatk-bridge2.0-0
libatk-bridge2.0-0:i386
libvirt-clients
libvirt-daemon
libvirt-daemon-config-network
libvirt-daemon-config-nwfilter
libvirt-daemon-driver-lxc
libvirt-daemon-driver-qemu
libvirt-daemon-driver-vbox
libvirt-daemon-driver-xen
libvirt-daemon-system
libvirt-daemon-system-sysv
qemu-system-misc
qemu-system-misc:i386
virtinst
...-> i see that bridge-utlis is the only that is not pulled.
Last edited by chomwitt (2024-03-16 12:57:16)
Devuan(Chimaera)(Daedalus) DS+WM: XorgX11server+StumpVM
Offline
I have never used virt-manager. I tried using about a year ago, but quickly became annoyed with it and gave up. Since it is unnecessary and I can use QEMU without it, that is my current preference. I only mention that because some people seem to think that using virt-manager is a requirement.
Offline
I started using virt-manager and it kind felt ok . But it has that irritating config setup.
I wouldnt have problem trying command line. A small push with a link to a good tutorial
would help. I dont mean fancy one in a website that welcomes you with a thousand cookies
harvester companies. A simple one laying out simple concepts would be ok.
Devuan(Chimaera)(Daedalus) DS+WM: XorgX11server+StumpVM
Offline
I also use command line and spicy to connect to the console.
To set up a network bridge (all commands assume that the user executing qemu belongs to group kvm and VMs' IP numbers start with 192.168.128.2):
set up qemu-bridge-helper (has to be done once after upgrade):
chgrp kvm /usr/lib/qemu/qemu-bridge-helper
chmod 554 /usr/lib/qemu/qemu-bridge-helper
setcap CAP_NET_ADMIN,CAP_NET_RAW,CAP_NET_BIND_SERVICE=ep /usr/lib/qemu/qemu-bridge-helper
enable bridge at boot:
echo 1 > /proc/sys/net/ipv4/ip_forward
ip link add name brvm type bridge
ip addr add 192.168.128.1/24 dev brvm
ip link set up brvm
iptables -t nat -A POSTROUTING -s 192.168.128.0/24 -o eth+ -j MASQUERADE
iptables -t nat -A POSTROUTING -s 192.168.128.0/24 -o wlan+ -j MASQUERADE
pass this parameter when launching qemu:
-netdev tap,id=eth,br=brvm,helper=/usr/lib/qemu/qemu-bridge-helper
It is also possible to attach dhcpd and/or radvd to brvm for automatic address space management. By changing those ip commands above you may bridge brvm with workstation's ethernet interface and allow attaching VMs directly to the LAN.
Offline