Dev1 Galaxy Forum / lsblk command doesn't see my usb plugged Android phone

Re: lsblk command doesn't see my usb plugged Android phone

dummy@example.com (MiyoLinux) — Fri, 12 Aug 2022 15:48:32 +0000

You're correct. My mistake.
I got it confused with FreeBSD. Sorry. I'll edit my original post.
Thanks Ogis.

Re: lsblk command doesn't see my usb plugged Android phone

dummy@example.com (Ogis1975) — Fri, 12 Aug 2022 11:42:23 +0000

MiyoLinux wrote:

sudo apt install android-file-transfer

...for a GUI...

sudo apt install android-file-transfer-qt5

Hello. Your last specified command is not needed, because the package

android-file-transfer

already contains a graphical ui.

Re: lsblk command doesn't see my usb plugged Android phone

dummy@example.com (MiyoLinux) — Thu, 11 Aug 2022 20:08:21 +0000

sudo apt install android-file-transfer

~~...for a GUI...~~

~~sudo apt install android-file-transfer-qt5~~

See subsequent posts regarding the GUI...

Re: lsblk command doesn't see my usb plugged Android phone

dummy@example.com (drito) — Thu, 11 Aug 2022 17:39:45 +0000

Here the result.
Thanks for the info.

lsusb -v -s 16
Bus 002 Device 016: ID 0fce:51de Sony Ericsson Mobile Communications AB F3112
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0fce Sony Ericsson Mobile Communications AB
idProduct 0x51de
bcdDevice 2.28
iManufacturer 3 Sony
iProduct 4 F3112
iSerial 5 RQ3001MLTC
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x003e
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 0
iInterface 17 MTP
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x001c 1x 28 bytes
bInterval 6
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 1
iInterface 18 ADB Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0000
(Bus Powered)

Re: lsblk command doesn't see my usb plugged Android phone

dummy@example.com (chris2be8) — Thu, 11 Aug 2022 17:10:18 +0000

At a guess the system sees the phone, but not as a block device. Try lsusb and see if that says anything (if in doubt run lsusb with the phone plugged in and again after unplugging it). Then try lsusb -v -s

lsblk command doesn't see my usb plugged Android phone

dummy@example.com (drito) — Thu, 11 Aug 2022 10:48:38 +0000

Hello, I set the android usb mode to file transfer on the phone popup. libmtp-common is also installed. Neither spacefm or lsblk see the device.

But I was surprised by the Godot engine editor since it is able to detect the device and I even exported an runned a game from the PC.

Some info:

OS: Devuan GNU/Linux 4 (chimaera) x86_64
Host: 20BECTO1WW ThinkPad T540p
Kernel: 5.10.0-16-amd64
Uptime: 46 mins
Packages: 835 (dpkg), 16 (guix-user)
Shell: bash 5.1.8
Resolution: 1920x1080
WM: bspwm
Theme: Graphite-dark [GTK2/3]
Icons: Tela [GTK2/3]
Terminal: alacritty
CPU: Intel i5-4210M (4) @ 3.200GHz
GPU: Intel 4th Gen Core Processor

I forgot another info: the init system is runit.

I have no idea about what happens. Advices are welcome.